PREPARATION OF PLANT PROTECTION PRODUCT FOR APPLICATION:
The plant protection product calculated over the recommended dosage is first mixed with some water in a separate container. The tank of the application machine is half filled with water. While the mixer of the machine is running, mixed water is added to the tank. The mixing is continued and the tank is completed with water. Mixing process continues until the application is completed. Use the prepared plant protection product on the same day.
For seed application: The seed application can be done with a rotary application canister or a seed application machine that works with the spray principle. In the absence of suitable equipment, seeds are spread on a flat ground and applied in a way to provide a homogeneous coating. Since a seed with a plant protection product can change the previous seeder setting, it is recommended to repeat the seeder setting with mixed seed before planting. After use, the application tool should be thoroughly cleaned.
Before the application, the calibration of the application machine should be done. The amount of mixture to be given to a certain area should be well adjusted in order to provide a good coating. Applications should be done in cool hours of the day in windless or less windy weather conditions.
CLEANING OF THE SPRAYING MACHINE:
Empty the sprayer tank safely immediately after the application is completed. After filling the tank with clean water, run the mixer and spray system to ensure all parts are washed. Do not wash near water sources. Do not pour the washing water and waste into water sources.
HOW TO USE THE PLANT PROTECTION PRODUCT
Application is done in the form of seed application before planting. It is a liquid plant protection product, and the recommended amount of mixture of powder and liquid formulated preparations for 100 kg of seed is dissolved in 1-1.5 L of water and then the water is distributed homogeneously to the whole seed.
Cucurbita mildew (cucumber):
The application starts when the plants start to take a branch or with the first symptoms of mildew and is continued at 7-10 day intervals depending on the severity of the disease. Applications should be made throughout the plant, in particular, to cover the underside of the leaf.
Application is started when climatic conditions such as high humidity occur for the disease outlet or when the first symptoms of the disease are seen in the environment and the application is repeated at 10-12 day intervals depending on the severity of the disease.
For chemical control, application is started with the appearance of a white ash cover under 3-5 mm diameter brown spots on tomato leaves, or in places where the disease appears every year, when suitable conditions are seen for the disease. The application is continued at 10-12 intervals depending on the course of the disease and climatic conditions.
Crumbles in tobacco seedlings:
In tobacco seedlings, the soil is slightly moistened immediately after the seed is sown. Then plant protection product is applied. The application is repeated after 25-30 days.
INFORMATION ABOUT RESISTANCE:
Plant protection product named MASSOCARB is a fungicide classified as Group F4: 28 according to its mechanism of action. Repetitive applications of plant protection products with the same mechanism of action promote resistance development. For this reason, to delay developing resistance, do not exceed total application number of MASSOCARB in the same season. In cases where the application should be repeated, pay attention to the use of plant protection products with a different mechanism of action (except for Group F4: 28).
It does not mix with burgundy slurry and leaf fertilizers. When used as a seed application, it should be used alone without being mixed with any plant protection product.
Rinse well by putting clean water up to ¼ in the empty packages of the product used. Pour the rinse water into the application tank. Repeat this process 3 times.
It can cause headaches, dizziness, weakness, dark eyes, and fever.
FIRST AID MEASURES
After Inhalation: When inhaled, remove to fresh air and allow to rest. If worried, seek medical attention.
After Skin Contact: Carefully remove contaminated clothing. Wash the affected area with soap and water. If worried, seek medical attention.
After Eye Contact: Rinse with clean water for at least 15 minutes and seek medical attention.
After Swallowing: Rinse mouth with water. Do not induce vomiting. Keep the patient at rest and seek medical attention.
ANTIDOTE and TREATMENT
If the plant protection product is swallowed enough to prevent cholinesterase, Atropinsulfate is used as an antidote. If the plant protection product is taken less, symptomatic treatment is sufficient.
HAZARDOUS EXPRESSIONS (H)
H317: Causes allergic skin reactions.
EUH208: Contains Propamocarb hydrochloride. May cause an allergic reaction.
Precautionary Statements (P)
P261: Avoid breathing spray.
P272: Do not take contaminated clothing out of the office.
P280: Wear protective gloves / protective clothing / eye protection / face protection.
P302 + P352: IF ON SKIN: Wash with plenty of soap and water.
P333 + P313: If skin irritation or itching occurs: Get medical attention / attention.
P363: Wash contaminated clothing before reuse.
P501 Dispose of contents / container in accordance with local regulations.
EUH401: Follow the instructions for use to avoid risks to human health and the environment.
MATTERS TO BE CONSIDERED WHEN USING AND STORING
When stored unopened in its original packaging under normal (cool and dry) conditions, there is no change in the physical, chemical and biological properties of the product outside the tolerance limits for 2 years.
The manufacturers guarantee the quality of their products provided that they are sold in their original packaging. Manufacturers do not accept responsibility for any damage caused by incorrect storage of their products or deficiencies in following the recommendations.
LICENSE OWNER AND MANUFACTURER COMPANY
ERTAR KİMYA Agricultural Products Tools Manufacturing Market. Singing. ve Tic. Ltd. Sti.
Acıdere Osb Mah. Zafer Cad. No: 8 Saricam / ADANA
Tel: 0 (322) 456 19 44 Fax: 0 (322) 456 19 47
PLANT AND HAZARDOUS ORGANISMS TO BE USED
|Plant Name||Harmful Organism Name||Administration dose||Time Between Last Application and Harvest|
|SUNFLOWER||Sunflower mildew (Plasmopara helianthi)||500 ml/100 kg Seed||—|
|CROP (Field)||Cucurbit mildew (Pseudoperonospora cubensis)||250 ml/da||3 day|
|POTATO||Potato Mildew (Phytophthora infestans)||250 ml/da||3 day|
|TOBACCO (Seedling)||Crumbling tobacco seedlings (Pythium spp.)||7.5 ml /m2
(With 3-4 L of water)
|Downy mildew(Phytophthora infestans)||250 ml/100 L water||3 day|